TIOS 3.1.0.0 release is out

[maleficium]

Originally Posted by HUEY

Yes, I'm in Windows XPsp3

Oh yeah, I forgot to mention that I'm also using SP3.

I was a little panicked too when I realized it's not only me. I just did a fresh reinstall of XP on my studio PC and a had a mind set for a nice Ambient groove session. On the other hand I had good time to hone my theremin skills while waiting for replies from Access support and the forum people.

By the way, nothing helpful from access support yet. They're just double checking if I installed the vst .dll to the right location and such. I quess they're running around office, chain smoking and sweating, trying to figure what the hell went wrong

[HUEY]

When I'm finished working I will try to roll back to 3.0.5. There are many reports that this doesn't work and the problem persists.
There is 1 report on the access forum of succesfully rolling back to 3.0.5 so it can be done i guess

best r

[absynth]

please try the following:

start your vc controll center let it connect->which os is shown on your virus ti display (not vc controll)?? 3.04?

could this be the problem?

anyone tryed to go back to 3.04?

[maleficium]

Originally Posted by HUEY

When I'm finished working I will try to roll back to 3.0.5. There are many reports that this doesn't work and the problem persists.
There is 1 report on the access forum of succesfully rolling back to 3.0.5 so it can be done i guess

best r

Yeah, I'm simulatneously reading the access forums too I just can't seem to log on there (which really doesn't bother me right now as much as the 3.1 thingie)

I remember reading about someone Exit-power up - forcing the 3.0.5 back in. How exactly is this done? Do I have to edit registry entries and such?

I think I'll go right away to the studio to try this out, if someone there is nice enough to give good instructions.

[HUEY]

Rolling back to a older OS:

*Do a good de-installation of drivers and software (via installed software in Windows)
*Force the Virus in update mode (holding down the exit button while powering up) and run the the older software installer (in this case 3.0.5)
*after completion, remove the power cable for 30 sec.
*start the Virus Ti up while holding down the ARP-edit button (this resets the virus and is always a good thing to do after a update)

This method always worked for me

Good luck

[maleficium]

Originally Posted by HUEY

Rolling back to a older OS:

*Do a good de-installation of drivers and software (via installed software in Windows)
*Force the Virus in update mode (holding down the exit button while powering up) and run the the older software installer (in this case 3.0.5)
*after completion, remove the power cable for 30 sec.
*start the Virus Ti up while holding down the ARP-edit button (this resets the virus and is always a good thing to do after a update)

Okay thanks. I'll just have to fill myself up with caffeine and off I go. I'll keep you posted on what's happening with the force "downdating".

[HUEY]

Originally Posted by maleficium

Okay thanks. I'll just have to fill myself up with caffeine and off I go. I'll keep you posted on what's happening with the force "downdating".

Please keep me informed. When this works for you it will also works for many others and me

Many people just run the older installer over the new version and this will NOT work. Then you will also get a driver mismatch error etc.

again good luck!

[absynth]

Hi,

I can confirm that it was a wrong label in the installation.
Only 3.1.0.00 Window is affected.

I've updated the Windows-Installer, so, if you are experiencing that specific version mismatch please download the current version.

-timo

i hope it works now!