The Unofficial Access Virus & Virus TI Forum - since 2002

The Unofficial Access Virus & Virus TI Forum - since 2002 (http://www.infekted.org/virus/forum.php)
-   General discussion about Access Virus (http://www.infekted.org/virus/forumdisplay.php?f=105)
-   -   Virus TIx knobs (http://www.infekted.org/virus/showthread.php?t=34704)

NoLie6 19.02.2021 07:58 AM

Virus TIx knobs
 
Is it only me who is thinking the knobs of the Virus TIx should have been made as unlimited circular knobs, rather than knobs with a left and right end/stop?

Of course if you have such unlimited knobs, you would not visually see at which position the knob is. BUT, also with Virus knobs, with hard end/stops, you will not see it anyway.

If you load a patch, your CUTOFF knob might be standing at full, but the patch value has it very low near 0.

That is reason why I am thinking it should be unlimited knobs. Because the current knobs have no advantage. But they have a big disadvantage. If you loaded a patch, and just want to slightly change the value of a knob, it will not work. The value in the above example would jumb from near 0 to almost full, when I slightly want to decrease it from the current value.

Of course the virus is just as the virus is:-)

Just thinking if someone else is also constantly thinking like that.

Edit:
Oh, I found an advantage of the current knobs: If you are playing with a knob, while not looking at the virus, you will have the physical feedback when you reaching the lowest or highest possible value. Yes, this could be stated as an advantage:-)

MBTC 20.02.2021 01:04 AM

Quote:

Originally Posted by NoLie6 (Post 307369)
Is it only me who is thinking the knobs of the Virus TIx should have been made as unlimited circular knobs, rather than knobs with a left and right end/stop?

Of course if you have such unlimited knobs, you would not visually see at which position the knob is. BUT, also with Virus knobs, with hard end/stops, you will not see it anyway.

If you load a patch, your CUTOFF knob might be standing at full, but the patch value has it very low near 0.

That is reason why I am thinking it should be unlimited knobs. Because the current knobs have no advantage. But they have a big disadvantage. If you loaded a patch, and just want to slightly change the value of a knob, it will not work. The value in the above example would jumb from near 0 to almost full, when I slightly want to decrease it from the current value.

Of course the virus is just as the virus is:-)

Just thinking if someone else is also constantly thinking like that.

Edit:
Oh, I found an advantage of the current knobs: If you are playing with a knob, while not looking at the virus, you will have the physical feedback when you reaching the lowest or highest possible value. Yes, this could be stated as an advantage:-)

What I have learned over the years is that limitations are the foundation of creativity. You will get the most of out it when you use those limitations as inspiration.

NoLie6 20.02.2021 08:53 AM

True!

And also the common phrase applies here too: Everthing has its downside! You can't have everything.

Timo 22.02.2021 09:40 PM

In my experience rotary encoders tend to be finicky, especially when they've aged, they become less responsive, inaccurate or jump values etc.

NoLie6 02.03.2021 05:54 PM

And additionally I came across a feature of the Virus, where Access Music has exactly addressed, what I am complaining:

In order to not have 'jumps' when turning certain knobs, it is possible to choose 'Snap' (instead of the default 'Jump') for Knob Behavior in the Config! That means you can turn a knob without any effect, until it reaches the default value. It will show a small arrow to remind you first going to the default.

Not bad. They already considered it!


All times are GMT. The time now is 05:32 PM.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2002-2022, Infekted.org